Philips TDA5051A Uživatelský manuál Strana 8

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 29
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 7
TDA5051A All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved.
Product data sheet Rev. 5 — 13 January 2011 8 of 29
NXP Semiconductors
TDA5051A
Home automation modem
OSC1 input and OSC2 output (OSC2 only used for driving external quartz crystal; must be left open-circuit when
using an external clock generator)
V
IH
HIGH-level input voltage 0.7V
DD
-V
DD
+0.5 V
V
IL
LOW-level input voltage 0.5 - 0.2V
DD
0.1 V
V
OH
HIGH-level output voltage I
OH
= 1.6 mA 2.4 - - V
V
OL
LOW-level output voltage I
OL
= 1.6 mA - - 0.45 V
Clock
f
osc
oscillator frequency 6.080 - 9.504 MHz
f
osc
/f
cr
ratio between oscillator and
carrier frequency
-64-
f
osc
/f
CLKOUT
ratio between oscillator and
clock output frequency
-2-
Transmission mode
f
cr
carrier frequency f
osc
=8.48MHz
[2]
- 132.5 - kHz
t
su
set-up time of the shaped
burst
f
osc
= 8.48 MHz;
see Figure 8
- 170 - μs
t
h
hold time of the shaped
burst
f
osc
= 8.48 MHz;
see Figure 8
- 170 - μs
t
W(DI)(min)
minimum pulse width of
DATA_IN
signal
f
osc
= 8.48 MHz;
see Figure 8
- 190 - μs
V
o(rms)
output carrier signal
(RMS value)
DATA_IN = LOW;
Z
L
= CISPR16
120 - 122 dBμV
I
o(max)
power amplifier maximum
output current (peak value)
DATA_IN = LOW;
Z
L
=1Ω
- 160 - mA
Z
o
output impedance of the
power amplifier
-5-Ω
V
O
output DC level at
pin TX_OUT
-2.5-V
THD total harmonic distortion on
CISPR16 load with the
coupling network (measured
on the first ten harmonics)
V
o(rms)
= 121 dBμV on
CISPR16 load;
f
osc
= 8.48 MHz;
DATA_IN
=LOW
(no modulation);
see Figure 3
and
Figure 22
- 55 - dB
B
20dB
bandwidth of the shaped
output signal (at 20 dB)
on CISPR16 load with the
coupling network
V
o(rms)
= 121 dBμV on
CISPR16 load;
f
osc
= 8.48 MHz;
DATA_IN = 300 Hz;
duty factor = 50 %;
see Figure 4
- 3000 - Hz
Table 5. Characteristics …continued
V
DDD
=V
DDA
=5V
±
5%; T
amb
=
40
°
C to +85
°
C; V
DDD
connected to V
DDA
; DGND connected to AGND.
Symbol Parameter Conditions Min Typ Max Unit
Zobrazit stránku 7
1 2 3 4 5 6 7 8 9 10 11 12 13 ... 28 29

Komentáře k této Příručce

Žádné komentáře