Philips LC7181 Uživatelský manuál Strana 1

Home Cinema ProjectorGarbo MatchlinePhilipsUser guideEnglish

3. Set up >• Place the projector on a stable, level surface, out of direct sunlight and away from sources ofexcessive dust,dirt, heat, water, mois

• Use the Zoom ring to adjust the size of the image.• Use the Focus ring to adjust the focus of the image.To raise:• Keep knob A pressed and lift to r

Video inputThe projector accepts the input signal of all major video formats, including NTSC 3.58, 4.43,PAL B, G, D, H, I, N, M and SECAM signals.The

>1 Connect the Video (out) socket of a VCR, Laser Disc player, video camera or TV to theVideo (in) socket of the projector.For this, use the video/

>Pr,Y, Pb/Cr,Y, Cb1 Connect the Component in sockets of the projector to the appropriate output sockets ofyour Component- or HDTV-video equipment (

<RGBS1 Connect the Scart/RCA Component Video adapter supplied (1) to the Scart connector ofyour Component- or HDTV-video equipment2 Connect the Com

>PC/Macintosh1 Connect the Data (out) socket of the computer to the Computer (in) socket of theprojector and secure the plugs by tightening the thu

Connecting to an external monitor1 Connect the VGA Y connector marked ‘Projector’ (5a), of an optional VGA Y-cable, to theComputer (in) socket of your

<1 Press the Standby button to switch on the projector.– The Standby indicator lights up orange.– When the projection lamp is on, the Standby indic

>All video and data adjustments and settings (except A/V Mute) are done via On Screen Displaysand with help of Menu, OK and Cursor Control on the p

>4Packaging contents 4Optional accessories 45-9Controls 5-6Remote control 7-8Connections 910-11Positioning the projector and screen

COMPUTER MODEMain menu Sub menu SettingDisplay Picture In Picture Off, Small, Medium, LargeSource Auto,Video,S-VideoPosition Cursor controlledposition

>1 Press Menu.– The menu bar appears on the screen.The first item is highlighted and its sub menu is shown.Depending on the selected source (Video,

>For Video/S-Video signal input, the following ‘Picture’ and ‘Display’ adjustments can be made:Picture adjustments• Press Menu and select ‘Picture’

>For computer signal input, the following ‘Picture’ and ‘Display’ adjustments can be made.Picture adjustments• Press Menu and select ‘Picture’ in t

>Some examplesThe following ‘Display’ adjustment procedures, follow a slightly different sequence of actions, ormay need some further explanation.P

Digital Zoom/Magnification‘Digital Zoom’ is used to enlarge a part of the picture.1 Press Menu.– The menu bar will appear.2 Use Cursor Control to move

ShiftThe Shift function adjusts the computer image in horizontal and vertical direction to centre it onthe screen.This function is only active when ‘A

<Audio adjustments• Press Menu and select Audio in the menu bar. The following Audio adjustments can now bemade for both Computer, Component and Vi

>Switch off and disconnect the projector before cleaning.1 Press the Standby button twice to switch off the projector.– The Standby indicator start

>When operation time reaches the last 100 hours of the average lamplife, the message ‘Warning:lamplife has almost expired’will be displayed on the

<18-27Preparation 18General 18Messages 18General explanation 18Feedback messages 18Some examples 18On Screen Display Menu 19-27Menu

<5 Unscrew screw B.6 Grasp the lamp holder handle and carefully pull the lamp holder out of the projector.• Do not tilt. If the inner tube is broke

>If a fault occurs, first check the points listed below before taking the projector for repair.If you are unable to remedy a problem by following t

In Data mode– Input resolution is too high (and keystoning is applied).• If you wish to keep the keystone correction, decrease the input resolution un

>– Distance is too great.• Reduce distance.– Batteries are exhausted.• Replace batteries (see ‘Inserting the batteries in the remote control’).– IR

General:• Check that the batteries are installed properly in the remote control and/or replace thebatteries.• Check that the projector receives the si

<Congratulations on your purchase of one of the most sophisticated and reliable products on themarket today.We are sure that, used properly, it wil

>To mute the sound of the projector and to mute the picture.To select the current projection source (Video, S-Video, Component, RGBS, Computer).The

<To adjust the vertical angle of the projector.To connect the projector to the mains.To insert an optional locking device (Kensington lock).Height/

2. Functional overviewThe ProntoNEO remote control supplied is an intelligent remote control that can be used forvirtually all audio and video devices

Soft buttonsTo switch the projector in or out of the Power/Standby mode.To select the current projection source (Video, S-Video, Component, RGBS, Comp

Video source connectionsInput sockets to connect to DVD- and HDTV-video equipmentThese sockets can be connected to the following output sockets: RGB-Y